ebooksgratis.com

See also ebooksgratis.com: no banners, no cookies, totally FREE.

CLASSICISTRANIERI HOME PAGE - YOUTUBE CHANNEL
Privacy Policy Cookie Policy Terms and Conditions
Viscosity - Wikipedia, the free encyclopedia

Viscosity

From Wikipedia, the free encyclopedia

Continuum mechanics
Conservation of mass
Conservation of momentum
Navier–Stokes equations
This box: view  talk  edit

Viscosity is a measure of the resistance of a fluid which is being deformed by either shear stress or extensional stress. It is commonly perceived as "thickness", or resistance to flow. Viscosity describes a fluid's internal resistance to flow and may be thought of as a measure of fluid friction. Thus, water is "thin", having a lower viscosity, while vegetable oil is "thick" having a higher viscosity. All real fluids (except superfluids) have some resistance to stress, but a fluid which has no resistance to shear stress is known as an ideal fluid or inviscid fluid. For example a high viscosity magma will create a tall volcano, because it cannot spread fast enough, low viscosity lava will create a shield volcano, which is large and wide.[1] The study of viscosity is known as rheology.

Contents

[edit] Etymology

The word "viscosity" derives from the Latin word "viscum" for mistletoe. A viscous glue was made from mistletoe berries and used for lime-twigs to catch birds.[2]

[edit] Viscosity coefficients

When looking at a value for viscosity, the number that one most often sees is the coefficient of viscosity. There are several different viscosity coefficients depending on the nature of applied stress and nature of the fluid. They are introduced in the main books on hydrodynamics[3][4] and rheology.[5]

Shear viscosity and dynamic viscosity are much better known than the others. That is why they are often referred to as simply viscosity. Simply put, this quantity is the ratio between the pressure exerted on the surface of a fluid, in the lateral or horizontal direction, to the change in velocity of the fluid as you move down in the fluid (this is what is referred to as a velocity gradient). For example, at room temperature, water has a nominal viscosity of 1.0 × 10-3 Pa∙s and motor oil has a nominal apparent viscosity of 250 × 10-3 Pa∙s.[6]

Extensional viscosity is widely used for characterizing polymers.
Volume viscosity is essential for Acoustics in fluids, see Stokes' law (sound attenuation) [7]

[edit] Newton's theory

Laminar shear of fluid between two plates. Friction between the fluid and the moving boundaries causes the fluid to shear. The force required for this action is a measure of the fluid's viscosity. This type of flow is known as a Couette flow.
Laminar shear of fluid between two plates. Friction between the fluid and the moving boundaries causes the fluid to shear. The force required for this action is a measure of the fluid's viscosity. This type of flow is known as a Couette flow.
Laminar shear, the non-constant gradient, is a result of the geometry the fluid is flowing through (e.g. a pipe).
Laminar shear, the non-constant gradient, is a result of the geometry the fluid is flowing through (e.g. a pipe).

In general, in any flow, layers move at different velocities and the fluid's viscosity arises from the shear stress between the layers that ultimately opposes any applied force.

Isaac Newton postulated that, for straight, parallel and uniform flow, the shear stress, τ, between layers is proportional to the velocity gradient, ∂u/∂y, in the direction perpendicular to the layers.

\tau=\eta \frac{\partial u}{\partial y}.

Here, the constant η is known as the coefficient of viscosity, the viscosity, the dynamic viscosity, or the Newtonian viscosity. Many fluids, such as water and most gases, satisfy Newton's criterion and are known as Newtonian fluids. Non-Newtonian fluids exhibit a more complicated relationship between shear stress and velocity gradient than simple linearity.

The relationship between the shear stress and the velocity gradient can also be obtained by considering two plates closely spaced apart at a distance y, and separated by a homogeneous substance. Assuming that the plates are very large, with a large area A, such that edge effects may be ignored, and that the lower plate is fixed, let a force F be applied to the upper plate. If this force causes the substance between the plates to undergo shear flow (as opposed to just shearing elastically until the shear stress in the substance balances the applied force), the substance is called a fluid. The applied force is proportional to the area and velocity of the plate and inversely proportional to the distance between the plates. Combining these three relations results in the equation F = η(Au/y), where η is the proportionality factor called the absolute viscosity (with units Pa·s = kg/(m·s) or slugs/(ft·s)). The absolute viscosity is also known as the dynamic viscosity, and is often shortened to simply viscosity. The equation can be expressed in terms of shear stress; τ = F/A = η(u/y). The rate of shear deformation is u / y and can be also written as a shear velocity, du/dy. Hence, through this method, the relation between the shear stress and the velocity gradient can be obtained.

James Clerk Maxwell called viscosity fugitive elasticity because of the analogy that elastic deformation opposes shear stress in solids, while in viscous fluids, shear stress is opposed by rate of deformation.

[edit] Viscosity measurement

Dynamic viscosity is measured with various types of viscometer. Close temperature control of the fluid is essential to accurate measurements, particularly in materials like lubricants, whose viscosity can double with a change of only 5 °C. For some fluids, it is a constant over a wide range of shear rates. These are Newtonian fluids.

The fluids without a constant viscosity are called Non-Newtonian fluids. Their viscosity cannot be described by a single number. Non-Newtonian fluids exhibit a variety of different correlations between shear stress and shear rate.

One of the most common instruments for measuring kinematic viscosity is the glass capillary viscometer.

In paint industries, viscosity is commonly measured with a Zahn cup, in which the efflux time is determined and given to customers. The efflux time can also be converted to kinematic viscosities (cSt) through the conversion equations.

Also used in paint, a Stormer viscometer uses load-based rotation in order to determine viscosity. The viscosity is reported in Krebs units (KU), which are unique to Stormer viscometers.

Vibrating viscometers can also be used to measure viscosity. These models use vibration rather than rotation to measure viscosity.

Extensional viscosity can be measured with various rheometers that apply extensional stress

Volume viscosity can be measured with acoustic rheometer.

[edit] Units of measure

[edit] Viscosity (dynamic/absolute viscosity)

Dynamic viscosity and absolute viscosity are synonymous. The IUPAC symbol for viscosity is the Greek symbol eta (η), and dynamic viscosity is also commonly referred to using the Greek symbol mu (μ). The SI physical unit of dynamic viscosity is the pascal-second (Pa·s), which is identical to kg·m−1·s−1. If a fluid with a viscosity of one Pa·s is placed between two plates, and one plate is pushed sideways with a shear stress of one pascal, it moves a distance equal to the thickness of the layer between the plates in one second.

The name poiseuille (Pl) was proposed for this unit (after Jean Louis Marie Poiseuille who formulated Poiseuille's law of viscous flow), but not accepted internationally. Care must be taken in not confusing the poiseuille with the poise named after the same person.

The cgs physical unit for dynamic viscosity is the poise[8] (P), named after Jean Louis Marie Poiseuille. It is more commonly expressed, particularly in ASTM standards, as centipoise (cP). The centipoise is commonly used because water has a viscosity of 1.0020 cP (at 20 °C; the closeness to one is a convenient coincidence).

1 P = 1 g·cm−1·s−1

The relation between poise and pascal-seconds is:

10 P = 1 kg·m−1·s−1 = 1 Pa·s
1 cP = 0.001 Pa·s = 1 mPa·s

[edit] Kinematic viscosity

In many situations, we are concerned with the ratio of the viscous force to the inertial force, the latter characterised by the fluid density ρ. This ratio is characterised by the kinematic viscosity (ν), defined as follows:

\nu = \frac {\mu} {\rho}.

where μ is the (dynamic or absolute) viscosity (in centipoise cP), and ρ is the density (in grams/cm^3), and ν is the kinematic viscosity (in centistokes cSt ).

Kinematic viscosity (Greek symbol: ν) has SI units Pa.s/(kg/m3) = m2·s−1. The cgs physical unit for kinematic viscosity is the stokes (abbreviated S or St), named after George Gabriel Stokes. It is sometimes expressed in terms of centistokes (cS or cSt). In U.S. usage, stoke is sometimes used as the singular form.

1 stokes = 100 centistokes = 1 cm2·s−1 = 0.0001 m2·s−1.
1 centistokes = 1 mm2·s-1 = 10-6m2·s−1

[edit] Saybolt Universal Viscosity

At one time the petroleum industry relied on measuring kinematic viscosity by means of the Saybolt viscometer, and expressing kinematic viscosity in units of Saybolt Universal Seconds (SUS). [9] Kinematic viscosity in centistoke can be converted from SUS according to the arithmetic and the reference tabel provided in ASTM D 2161. It can also be converted in computerized method, or vice versa.[10]

[edit] Relation to Mean Free Path of Diffusing Particles

In relation to diffusion, the kinematic viscosity provides a better understanding of the behavior of mass transport of a dilute species. Viscosity is related to shear stress and the rate of shear in a fluid, which illustrates its dependence on the mean free path, λ, of the diffusing particles.

From fluid mechanics, shear stress, τ, is the rate of change of velocity with distance perpendicular to the direction of movement.

\tau = \mu \frac{du}{dx}.

Interpreting shear stress as the time rate of change of momentum,p, per unit area (rate of momentum flux) of an arbitrary control surface gives

\tau = \frac{\dot{p}}{A} = \frac{\dot{m} u}{A}.

Further manipulation will show

\frac{\dot{p}}{u} = \dot{m} = \rho \bar{u} A \; \; \Rightarrow \; \;  \tau = \underbrace{2 \rho \bar{u} \lambda}_{\mu} \cdot \frac{du}{dx} \; \; \Rightarrow \; \; \nu = \frac{\mu}{\rho} = 2 \bar{u} \lambda

where

\dot{m} is the rate of change of mass
ρ is the density of the fluid
\bar{u} is the average molecular speed
μ is the dynamic viscosity.

[edit] Dynamic versus kinematic viscosity

Conversion between kinematic and dynamic viscosity is given by νρ = μ.

For example,

if ν = 0.0001 m2·s-1 and ρ = 1000 kg m-3 then μ = νρ = 0.1 kg·m−1·s−1 = 0.1 Pa·s
if ν = 1 St (= 1 cm2·s−1) and ρ = 1 g cm-3 then μ = νρ = 1 g·cm−1·s−1 = 1 P

A plot of the kinematic viscosity of air as a function of absolute temperature is available on the Internet.[11]

[edit] Example: viscosity of water

Because of its density of ρ = 1 g/cm3 (varies slightly with temperature), and its dynamic viscosity is near 1 mPa·s (see #Viscosity of water section), the viscosity values of water are, to rough precision, all powers of ten:

Dynamic viscosity:

μ = 1 mPa·s = 10-3 Pa·s = 1 cP = 10-2 poise

Kinematic viscosity:

ν = 1 cSt = 10-2 stokes = 1 mm²/s

[edit] Molecular origins

Pitch has a viscosity approximately 100 billion times that of water.
Pitch has a viscosity approximately 100 billion times that of water.

The viscosity of a system is determined by how molecules constituting the system interact. There are no simple but correct expressions for the viscosity of a fluid. The simplest exact expressions are the Green-Kubo relations for the linear shear viscosity or the Transient Time Correlation Function expressions derived by Evans and Morriss in 1985. Although these expressions are each exact in order to calculate the viscosity of a dense fluid, using these relations requires the use of molecular dynamics computer simulation.

[edit] Gases

Viscosity in gases arises principally from the molecular diffusion that transports momentum between layers of flow. The kinetic theory of gases allows accurate prediction of the behavior of gaseous viscosity.

Within the regime where the theory is applicable:

  • Viscosity is independent of pressure and
  • Viscosity increases as temperature increases.

James Clerk Maxwell published a famous paper in 1866 using the kinetic theory of gases to study gaseous viscosity. (Reference: J.C. Maxwell, "On the viscosity or internal friction of air and other gases", Philosophical Transactions of the Royal Society of London, vol. 156 (1866), pp. 249-268.)

[edit] Effect of temperature on the viscosity of a gas

Sutherland's formula can be used to derive the dynamic viscosity of an ideal gas as a function of the temperature:

 {\eta} = {\eta}_0 \frac {T_0+C} {T + C} \left (\frac {T} {T_0} \right )^{3/2}

where:

  • η = viscosity in (Pa·s) at input temperature T
  • η0 = reference viscosity in (Pa·s) at reference temperature T0
  • T = input temperature in kelvin
  • T0 = reference temperature in kelvin
  • C = Sutherland's constant for the gaseous material in question

Valid for temperatures between 0 < T < 555 K with an error due to pressure less than 10% below 3.45 MPa

Sutherland's constant and reference temperature for some gases

Gas C

[K]

T0

[K]

η0

[10-6 Pa s]

air 120 291.15 18.27
nitrogen 111 300.55 17.81
oxygen 127 292.25 20.18
carbon dioxide 240 293.15 14.8
carbon monoxide 118 288.15 17.2
hydrogen 72 293.85 8.76
ammonia 370 293.15 9.82
sulfur dioxide 416 293.65 12.54
helium 79.4 [12] 273 19 [13]

(also see: [14])

[edit] Viscosity of a dilute gas

The Chapman-Enskog equation[15] may be used to estimate viscosity for a dilute gas. This equation is based on semi-theorethical assumption by Chapman and Enskoq. The equation requires three empirically determined parameters: the collision diameter (σ), the maximum energy of attraction divided by the Boltzmann constant (є/к) and the collision integral (ω(T*)).

 {\eta}_0 \times 10^7 = {266.93}\frac {(MT)^{1/2}} {\sigma^{2}\omega(T^*)}
  • T*=κT/ε Reduced temperature (dimensionless)
  • η0 = viscosity for dilute gas (uP)
  • M = molecular mass (g/mol)
  • T = temperature (K)
  • σ = the collision diameter (Å)
  • ε / κ = the maximum energy of attraction divided by the Boltzmann constant (K)
  • ωη = the collision integral

[edit] Liquids

In liquids, the additional forces between molecules become important. This leads to an additional contribution to the shear stress though the exact mechanics of this are still controversial.[citation needed] Thus, in liquids:

  • Viscosity is independent of pressure (except at very high pressure); and
  • Viscosity tends to fall as temperature increases (for example, water viscosity goes from 1.79 cP to 0.28 cP in the temperature range from 0 °C to 100 °C); see temperature dependence of liquid viscosity for more details.

The dynamic viscosities of liquids are typically several orders of magnitude higher than dynamic viscosities of gases.

[edit] Viscosity of blends of liquids

The viscosity of the blend of two or more liquids can be estimated using the Refutas equation[16][17]. The calculation is carried out in three steps.

The first step is to calculate the Viscosity Blending Number (VBN) (also called the Viscosity Blending Index) of each component of the blend:

(1) \mbox{VBN} = 14.534 \times ln[ln(v + 0.8)] + 10.975\,

where v is the kinematic viscosity in centistokes (cSt). It is important that the kinematic viscosity of each component of the blend be obtained at the same temperature.

The next step is to calculate the VBN of the blend, using this equation:

(2) \mbox{VBN}_\mbox{Blend} = [x_A \times \mbox{VBN}_A] + [x_B \times \mbox{VBN}_B] + ... + [x_N \times \mbox{VBN}_N]\,

where xX is the mass fraction of each component of the blend.

Once the viscosity blending number of a blend has been calculated using equation (2), the final step is to determine the kinematic viscosity of the blend by solving equation (1) for v:

(3) v = e^{e^{\frac{VBN_{Blend} - 10.975}{14.534}}} -  0.8

where VBNBlend is the viscosity blending number of the blend.

[edit] Viscosity of selected substances

The viscosity of air and water are by far the two most important materials for aviation aerodynamics and shipping fluid dynamics. Temperature plays the main role in determining viscosity.

[edit] Viscosity of air

The viscosity of air depends mostly on the temperature. At 15.0 °C, the viscosity of air is 1.78 × 10−5 kg/(m·s) or 1.78 × 10−4 P. One can get the viscosity of air as a function of temperature from the Gas Viscosity Calculator

[edit] Viscosity of water

The viscosity of water is 8.90 × 10−4 Pa·s or 8.90 × 10−3 dyn·s/cm2 or 0.890 cP at about 25 °C.
As a function of temperature T (K): μ(Pa·s) = A × 10B/(TC)
where A=2.414 × 10−5 Pa·s ; B = 247.8 K ; and C = 140 K.

Viscosity of water at different temperatures is listed below.

Temperature

[ºC]

viscosity

[Pa·s]

10 1.308 × 10−3
20 1.003 × 10−3
30 7.978 × 10−4
40 6.531 × 10−4
50 5.471 × 10−4
60 4.668 × 10−4
70 4.044 × 10−4
80 3.550 × 10−4
90 3.150 × 10−4
100 2.822 × 10−4

[edit] Viscosity of various materials

Example of the viscosity of milk and water. Liquids with higher viscosities will not make such a splash when poured at the same velocity.
Example of the viscosity of milk and water. Liquids with higher viscosities will not make such a splash when poured at the same velocity.
Honey being drizzled.
Honey being drizzled.
Peanut butter is a semi-solid and so can hold peaks.
Peanut butter is a semi-solid and so can hold peaks.

Some dynamic viscosities of Newtonian fluids are listed below:

Gases (at 0 °C):

viscosity

[Pa·s]

hydrogen 8.4 × 10−6
air 17.4 × 10−6
xenon 2.12 × 10−5

Liquids (at 25 °C):

viscosity

[Pa·s]

viscosity

[cP]

liquid nitrogen @ 77K 1.58 × 10−4 0.158
acetone* 3.06 × 10−4 0.306
methanol* 5.44 × 10−4 0.544
benzene* 6.04 × 10−4 0.604
water 8.94 × 10−4 0.894
ethanol* 1.074 × 10−3 1.074
mercury* 1.526 × 10−3 1.526
nitrobenzene* 1.863 × 10−3 1.863
propanol* 1.945 × 10−3 1.945
Ethylene glycol 1.61 × 10−2 16.1
sulfuric acid* 2.42 × 10−2 24.2
olive oil .081 81
glycerol* .934 934
castor oil* .985 985
corn syrup* 1.3806 1380.6
HFO-380 2.022 2022
pitch 2.3 × 108 2.3 × 1011

* Data from CRC Handbook of Chemistry and Physics, 73rd edition, 1992-1993.

Fluids with variable compositions, such as honey, can have a wide range of viscosities.

A more complete table can be found at Transwiki, including the following:

viscosity

[cP]

honey 2,000–10,000
molasses 5,000–10,000
molten glass 10,000–1,000,000
chocolate syrup 10,000–25,000
molten chocolate* 45,000–130,000 [18]
ketchup* 50,000–100,000
peanut butter ~250,000
shortening* ~250,000

* These materials are highly non-Newtonian.

[edit] Viscosity of solids

On the basis that all solids flow to a small extent in response to shear stress some researchers[19][20] have contended that substances known as amorphous solids, such as glass and many polymers, may be considered to have viscosity. This has led some to the view that solids are simply liquids with a very high viscosity, typically greater than 1012 Pa·s. This position is often adopted by supporters of the widely held misconception that glass flow can be observed in old buildings. This distortion is more likely the result of glass making process rather than the viscosity of glass.[21]

However, others argue that solids are, in general, elastic for small stresses while fluids are not.[22] Even if solids flow at higher stresses, they are characterized by their low-stress behavior. Viscosity may be an appropriate characteristic for solids in a plastic regime. The situation becomes somewhat confused as the term viscosity is sometimes used for solid materials, for example Maxwell materials, to describe the relationship between stress and the rate of change of strain, rather than rate of shear.

These distinctions may be largely resolved by considering the constitutive equations of the material in question, which take into account both its viscous and elastic behaviors. Materials for which both their viscosity and their elasticity are important in a particular range of deformation and deformation rate are called viscoelastic. In geology, earth materials that exhibit viscous deformation at least three times greater than their elastic deformation are sometimes called rheids.

[edit] Viscosity of amorphous materials

Common glass viscosity curves.
Common glass viscosity curves.[23]

Viscous flow in amorphous materials (e.g. in glasses and melts)[24][25][26] is a thermally activated process:

\eta = A \cdot e^{Q/RT}

where Q is activation energy, T is temperature, R is the molar gas constant and A is approximately a constant.

The viscous flow in amorphous materials is characterized by a deviation from the Arrhenius-type behavior: Q changes from a high value QH at low temperatures (in the glassy state) to a low value QL at high temperatures (in the liquid state). Depending on this change, amorphous materials are classified as either

  • strong when: QHQL < QL or
  • fragile when: Q_H - Q_L \ge Q_L

The fragility of amorphous materials is numerically characterized by the Doremus’ fragility ratio:

RD = QH / QL

and strong material have R_D < 2\; whereas fragile materials have R_D \ge 2

The viscosity of amorphous materials is quite exactly described by a two-exponential equation:

\eta = A_1 \cdot T \cdot [1 + A_2 \cdot e^{B/RT}] \cdot [1 + C \cdot e^{D/RT}]

with constants A1,A2,B,C and D related to thermodynamic parameters of joining bonds of an amorphous material.

Not very far from the glass transition temperature, Tg, this equation can be approximated by a Vogel-Tammann-Fulcher (VTF) equation or a Kohlrausch-type stretched-exponential law.

If the temperature is significantly lower than the glass transition temperature, T < Tg, then the two-exponential equation simplifies to an Arrhenius type equation:

\eta = A_LT \cdot e^{Q_H/RT}

with:

QH = Hd + Hm

where Hd is the enthalpy of formation of broken bonds (termed configurons) and Hm is the enthalpy of their motion. When the temperature is less than the glass transition temperature, T < Tg, the activation energy of viscosity is high because the amorphous materials are in the glassy state and most of their joining bonds are intact.

If the temperature is highly above the glass transition temperature, T > Tg, the two-exponential equation also simplifies to an Arrhenius type equation:

\eta = A_HT\cdot e^{Q_L/RT}

with:

QL = Hm

When the temperature is higher than the glass transition temperature, T > Tg, the activation energy of viscosity is low because amorphous materials are melt and have most of their joining bonds broken which facilitates flow.

[edit] Volume (bulk) viscosity

The negative-one-third of the trace of the stress tensor is often identified with the thermodynamic pressure,

-{1\over3}T_a^a = p,

which only depends upon the equilibrium state potentials like temperature and density (equation of state). In general, the trace of the stress tensor is the sum of thermodynamic pressure contribution plus another contribution which is proportional to the divergence of the velocity field. This constant of proportionality is called the volume viscosity.

[edit] Eddy viscosity

In the study of turbulence in fluids, a common practical strategy for calculation is to ignore the small-scale vortices (or eddies) in the motion and to calculate a large-scale motion with an eddy viscosity that characterizes the transport and dissipation of energy in the smaller-scale flow (see large eddy simulation). Values of eddy viscosity used in modeling ocean circulation may be from 5x104 to 106 Pa·s depending upon the resolution of the numerical grid.

[edit] Fluidity

The reciprocal of viscosity is fluidity, usually symbolized by φ = 1 / η or F = 1 / η, depending on the convention used, measured in reciprocal poise (cm·s·g-1), sometimes called the rhe. Fluidity is seldom used in engineering practice.

The concept of fluidity can be used to determine the viscosity of an ideal solution. For two components a and b, the fluidity when a and b are mixed is

F \approx \chi_a F_a + \chi_b F_b

which is only slightly simpler than the equivalent equation in terms of viscosity:

\eta \approx \frac{1}{\chi_a /\eta_a + \chi_b/\eta_b}

where χa and χb is the mole fraction of component a and b respectively, and ηa and ηb are the components pure viscosities.

[edit] The linear viscous stress tensor

(See Hooke's law and strain tensor for an analogous development for linearly elastic materials.)

Viscous forces in a fluid are a function of the rate at which the fluid velocity is changing over distance. The velocity at any point \mathbf{r} is specified by the velocity field \mathbf{v}(\mathbf{r}). The velocity at a small distance d\mathbf{r} from point \mathbf{r} may be written as a Taylor series:

\mathbf{v}(\mathbf{r}+d\mathbf{r}) = \mathbf{v}(\mathbf{r})+\frac{d\mathbf{v}}{d\mathbf{r}}d\mathbf{r}+\ldots

where \frac{d\mathbf{v}}{d\mathbf{r}} is shorthand for the dyadic product of the del operator and the velocity:

\frac{d\mathbf{v}}{d\mathbf{r}} = \begin{bmatrix}
\frac{\partial v_x}{\partial x} & \frac{\partial v_x}{\partial y} & \frac{\partial v_x}{\partial z}\\
\frac{\partial v_y}{\partial x} & \frac{\partial v_y}{\partial y} & \frac{\partial v_y}{\partial z}\\
\frac{\partial v_z}{\partial x} & \frac{\partial v_z}{\partial y}&\frac{\partial v_z}{\partial z}
\end{bmatrix}

This is just the Jacobian of the velocity field. Viscous forces are the result of relative motion between elements of the fluid, and so are expressible as a function of the velocity field. In other words, the forces at \mathbf{r} are a function of \mathbf{v}(\mathbf{r}) and all derivatives of \mathbf{v}(\mathbf{r}) at that point. In the case of linear viscosity, the viscous force will be a function of the Jacobian tensor alone. For almost all practical situations, the linear approximation is sufficient.

If we represent x, y, and z by indices 1, 2, and 3 respectively, the i,j component of the Jacobian may be written as \partial_i v_j where \partial_i is shorthand for \partial /\partial x_i. Note that when the first and higher derivative terms are zero, the velocity of all fluid elements is parallel, and there are no viscous forces.

Any matrix may be written as the sum of an antisymmetric matrix and a symmetric matrix, and this decomposition is independent of coordinate system, and so has physical significance. The velocity field may be approximated as:

v_i(\mathbf{r}+d\mathbf{r}) = v_i(\mathbf{r})+\frac{1}{2}\left(\partial_i v_j-\partial_j v_i\right)dr_i + \frac{1}{2}\left(\partial_i v_j+\partial_j v_i\right)dr_i

where Einstein notation is now being used in which repeated indices in a product are implicitly summed. The second term from the right is the asymmetric part of the first derivative term, and it represents a rigid rotation of the fluid about \mathbf{r} with angular velocity ω where:

\omega=\frac12 \mathbf{\nabla}\times \mathbf{v}=\frac{1}{2}\begin{bmatrix}
\partial_2 v_3-\partial_3 v_2\\
\partial_3 v_1-\partial_1 v_3\\
\partial_1 v_2-\partial_2 v_1
\end{bmatrix}

For such a rigid rotation, there is no change in the relative positions of the fluid elements, and so there is no viscous force associated with this term. The remaining symmetric term is responsible for the viscous forces in the fluid. Assuming the fluid is isotropic (i.e. its properties are the same in all directions), then the most general way that the symmetric term (the rate-of-strain tensor) can be broken down in a coordinate-independent (and therefore physically real) way is as the sum of a constant tensor (the rate-of-expansion tensor) and a traceless symmetric tensor (the rate-of-shear tensor):


\frac{1}{2}\left(\partial_i v_j+\partial_j v_i\right) 
= 
\underbrace{\frac{1}{3}\partial_k v_k \delta_{ij}}_{\text{rate-of-expansion tensor}}
+
\underbrace{\left(\frac{1}{2}\left(\partial_i v_j+\partial_j v_i\right)-\frac{1}{3}\partial_k v_k \delta_{ij}\right)}_{\text{rate-of-shear tensor}}

where δij is the unit tensor. The most general linear relationship between the stress tensor \mathbf{\sigma} and the rate-of-strain tensor is then a linear combination of these two tensors:[27]

\sigma_{visc;ij} = \zeta\partial_k v_k \delta_{ij}+
\eta\left(\partial_i v_j+\partial_j v_i-\frac{2}{3}\partial_k v_k \delta_{ij}\right)

where ζ is the coefficient of bulk viscosity (or "second viscosity") and η is the coefficient of (shear) viscosity.

The forces in the fluid are due to the velocities of the individual molecules. The velocity of a molecule may be thought of as the sum of the fluid velocity and the thermal velocity. The viscous stress tensor described above gives the force due to the fluid velocity only. The force on an area element in the fluid due to the thermal velocities of the molecules is just the hydrostatic pressure. This pressure term ( pδij) must be added to the viscous stress tensor to obtain the total stress tensor for the fluid.

\sigma_{ij} = -p\delta_{ij}+\sigma_{visc;ij}\,

The infinitesimal force dFi on an infinitesimal area dAi is then given by the usual relationship:

dF_i=\sigma_{ij}dA_j\,

[edit] See also

[edit] References

  1. ^ Symon, Keith (1971). Mechanics, Third Edition, Addison-Wesley. ISBN 0-201-07392-7. 
  2. ^ The Online Etymology Dictionary
  3. ^ Happel, J. and Brenner , H. "Low Reynolds number hydrodynamics", Prentice-Hall, (1965)
  4. ^ Landau, L.D. and Lifshitz, E.M. "Fluid mechanics", Pergamon Press,(1959)
  5. ^ Barnes, H.A. "A Handbook of Elementary Rheology", Institute of Non-Newtonian Fluid mechanics, UK (2000)
  6. ^ Raymond A. Serway (1996). Physics for Scientists & Engineers, 4th Edition, Saunders College Publishing. ISBN 0-03-005932-1. 
  7. ^ Dukhin, A.S. and Goetz, P.J. "Ultrasound for characterizing colloids", Elsevier, (2002)
  8. ^ IUPAC definition of the Poise
  9. ^ ASTM D 2161, Page one,(2005)
  10. ^ Quantities and Units of Viscosity
  11. ^ James Ierardi's Fire Protection Engineering Site
  12. ^ data constants for sutherland's formula
  13. ^ Viscosity of liquids and gases
  14. ^ http://www.epa.gov/EPA-AIR/2005/July/Day-13/a11534d.htm
  15. ^ J.O. Hirshfelder, C.F. Curtis and R.B. Bird (1964). Molecular theory of gases and liquids, First Edition, Wiley. ISBN 0-471-40065-3. 
  16. ^ Robert E. Maples (2000). Petroleum Refinery Process Economics, 2nd Edition, Pennwell Books. ISBN 0-87814-779-9. 
  17. ^ C.T. Baird (1989), Guide to Petroleum Product Blending, HPI Consultants, Inc. HPI website
  18. ^ Chocolate Processing. Brookfield Engineering website. Retrieved on 2007-12-03.
  19. ^ Elert, Glenn. Viscosity. The Physics Hypertextbook.
  20. ^ The Properties of Glass , page 6, retrieved on August 1, 2007
  21. ^ "Antique windowpanes and the flow of supercooled liquids", by Robert C. Plumb, (Worcester Polytech. Inst., Worcester, MA, 01609, USA), J. Chem. Educ. (1989), 66 (12), 994-6
  22. ^ Gibbs, Philip. Is Glass a Liquid or a Solid?. Retrieved on 2007-07-31.
  23. ^ Viscosity calculation of glasses
  24. ^ R.H.Doremus (2002). "Viscosity of silica". J. Appl. Phys. 92 (12): 7619-7629. doi:10.1063/1.1515132. ISSN 0021-8979. 
  25. ^ M.I. Ojovan and W.E. Lee (2004). "Viscosity of network liquids within Doremus approach". J. Appl. Phys. 95 (7): 3803-3810. doi:10.1063/1.1647260. ISSN 0021-8979. 
  26. ^ M.I. Ojovan, K.P. Travis and R.J. Hand (2000). "Thermodynamic parameters of bonds in glassy materials from viscosity-temperature relationships". J. Phys.: Condensed matter 19 (41): 415107. ISSN 0953-8984. 
  27. ^ L.D. Landau and E.M. Lifshitz (translated from Russian by J.B. Sykes and W.H. Reid) (1997). Fluid Mechanics, 2nd Edition, Butterworth Heinemann. ISBN 0-7506-2767-0. 

[edit] Additional reading

Look up Viscosity in
Wiktionary, the free dictionary.
  • Massey, B. S. (1983). Mechanics of Fluids, Fifth Edition, Van Nostrand Reinhold (UK). ISBN 0-442-30552-4. 

[edit] External links


aa - ab - af - ak - als - am - an - ang - ar - arc - as - ast - av - ay - az - ba - bar - bat_smg - bcl - be - be_x_old - bg - bh - bi - bm - bn - bo - bpy - br - bs - bug - bxr - ca - cbk_zam - cdo - ce - ceb - ch - cho - chr - chy - co - cr - crh - cs - csb - cu - cv - cy - da - de - diq - dsb - dv - dz - ee - el - eml - en - eo - es - et - eu - ext - fa - ff - fi - fiu_vro - fj - fo - fr - frp - fur - fy - ga - gan - gd - gl - glk - gn - got - gu - gv - ha - hak - haw - he - hi - hif - ho - hr - hsb - ht - hu - hy - hz - ia - id - ie - ig - ii - ik - ilo - io - is - it - iu - ja - jbo - jv - ka - kaa - kab - kg - ki - kj - kk - kl - km - kn - ko - kr - ks - ksh - ku - kv - kw - ky - la - lad - lb - lbe - lg - li - lij - lmo - ln - lo - lt - lv - map_bms - mdf - mg - mh - mi - mk - ml - mn - mo - mr - mt - mus - my - myv - mzn - na - nah - nap - nds - nds_nl - ne - new - ng - nl - nn - no - nov - nrm - nv - ny - oc - om - or - os - pa - pag - pam - pap - pdc - pi - pih - pl - pms - ps - pt - qu - quality - rm - rmy - rn - ro - roa_rup - roa_tara - ru - rw - sa - sah - sc - scn - sco - sd - se - sg - sh - si - simple - sk - sl - sm - sn - so - sr - srn - ss - st - stq - su - sv - sw - szl - ta - te - tet - tg - th - ti - tk - tl - tlh - tn - to - tpi - tr - ts - tt - tum - tw - ty - udm - ug - uk - ur - uz - ve - vec - vi - vls - vo - wa - war - wo - wuu - xal - xh - yi - yo - za - zea - zh - zh_classical - zh_min_nan - zh_yue - zu -