Storage ring

From Wikipedia, the free encyclopedia

A storage ring is a type of circular particle accelerator in which a continuous or pulsed particle beam may be kept circulating for a long period of time, up to many hours. Storage of a particular particle depends upon the mass, energy and usually charge of the particle being stored. Most commonly, storage rings are to store electrons, positrons, or protons. The most common application of storage rings is to store electrons which then radiate synchrotron radiation; there are over 50 facilities based on electron storage rings in the world today, and are used for a variety of studies in chemistry and biology. The most well-known application of storage rings is arguably their use in 'atom smashers', in which two counter-rotating beams of stored particles are brought into collision at discrete locations, the results of the subatomic interactions being studied in a surrounding particle detector. Examples of such accelerators are LHC, LEP, PEP-II, KEK-B, RHIC, Tevatron and HERA.

Technically speaking, a storage ring is a type of synchrotron. However, a conventional synchrotron serves to accelerate particles from a low to a high energy with the aid of radio-frequency accelerating cavities; a storage ring, as the name suggests, keeps particles stored at a constant energy, and radio-frequency cavities are only used to replace energy lost through synchrotron radiation and other processes.

1 Important considerations for storage of a particle beam
2 See also
3 References

[edit] Important considerations for storage of a particle beam

[edit] Magnets

A force must be applied to particles in such a way that they are constrained to move approximately in a circular path. This may be accomplished using either dipole electrostatic or dipole magnetic fields, but because most storage rings store relativistic charged particles it turns out that it is most practical to utilise magnetic fields produced by dipole magnets. However, electrostatic accelerators have been built to store very low energy particles, and quadrupole fields may be used to store (uncharged) neutrons; these are comparatively rare, however.

Dipole magnets alone only provide what is called weak focusing, and a storage ring composed of only these sorts of magnetic elements results in the particles have a relatively large beam size. Interleaving dipole magnets with an appropriate arrangement of quadrupole magnets can give a suitable strong focusing system that can give a much smaller beam size. The FODO and Chasman-Green structures are simple examples of strong focusing systems, but there are many others.

Dipole and quadrupole magnets deflect different particle energies by differing amounts, a property called chromaticity by analogy with physical optics. The spread of energies that is inherently present in any practical stored particle beam will therefore give rise to a spread of transverse and longitudinal focusing, as well as contributing to various particle beam instabilities . Sextupole magnets (and higher order magnets) are used to correct for this phenomenon, but in turn gives rise to nonlinear motion that is one of the main problems facing designers of storage rings.

[edit] Vacuum

As the bunches will travel many thousands of kilometers (considering that they will be moving at near the speed of light for many hours), any residual gas in the beam pipe will result in many, many collisions. This will have the effect of increasing the size of the bunch, and increasing the energy spread. Therefore, a better vacuum yields better beam dynamics. Also, single large-angle scattering events from either the residual gas, or from other particles in the bunch Touschek scattering, can eject particles far enough that they are lost on the walls of the accelerator vacuum vessel. This gradual loss of particles is called beam lifetime, and means that storage rings must be periodically injected with a new complement of particles.

[edit] Particle Injection and Timing

Injection of particles into a storage ring may be accomplished in a number of ways, depending on the upon the application of the storage ring. The simplest method uses one or more pulsed deflecting dipole magnets (injection kicker magnets) to steer an incoming train of particles onto the stored beam path; the kicker magnets are turned off before the stored train returns to the injection point, thus resulting in a stored beam. This method is sometimes called single-turn injection.

Multi-turn injection allows accumulation of many incoming trains of particles, for example if a large stored current is required. For particles such as protons where there is no significant beam damping, each injected pulse is placed onto a particular point in the stored beam transverse or longitudinal phase space, taking care not to eject previously-injected trains by using a careful arrangement of beam deflection and coherent oscillations in the stored beam. If there is significant beam damping, for example radiation damping of electrons due to synchrotron radiation, then an injected pulse may be placed on the edge of phase space and then left to damp in transverse phase space into the stored beam before injecting a further pulse. Typical damping times from synchrotron radiation are tens of milliseconds, allowing many pulses per second to be accumulated.

If extraction of particles is required (for example in a chain of accelerators), then single-turn extraction may be performed analogously with injection. Resonant extraction may also be employed.