Intel 8080
From Wikipedia, the free encyclopedia
| Intel 8080 Central processing unit |
|
 An Intel C8080A processor. |
|
| Produced: | mid 1974 |
| Manufacturer: | Intel |
| Max CPU clock: | 2 MHz |
| Instruction set: | pre x86 |
| Package: | 40 pin DIP |
The Intel 8080 was an early microprocessor designed and manufactured by Intel. The 8-bit CPU was released in April 1974 running at 2 MHz (at up to 500,000 instructions per second), and is generally considered to be the first truly usable microprocessor CPU design. It was implemented in NMOS.
Contents |
[edit] Description
[edit] Programming model
The Intel 8080 was the successor to the Intel 8008; this was due to its being assembly language source-compatible[vague], since it used the same instruction set developed by Computer Terminal Corporation. The 8080's large 40 pin DIP packaging permitted it to provide a 16-bit address bus and an 8-bit data bus, allowing easy access to 64 kilobytes of memory.
[edit] Registers
The processor had seven 8-bit registers, six of which (B, C, D, E, H, and L) could be combined into three 16-bit register pairs (BC, DE and HL[vague]) and the seventh of which was an 8-bit accumulator (A). It also had a 16-bit stack pointer to memory (replacing the 8008's internal stack), and a 16-bit program counter.
[edit] Commands
Most of the 8-bit operations were possible between the accumulator and either one of the registers or the memory cell, indexed by the 16-bit value of the register pair HL. Moving operations were supported between any two registers, or between any register and the HL-indexed memory cell. Due to the highly regular machine code format for MOV commands, the opcodes included those for moving a byte from a given register into the same register (MOV A,A , for instance). These commands were seldom used, however, unless programmed delays were needed. What would have been instruction to move from the HL-indexed memory cell into the same memory cell (i.e., MOV M,M) instead was HLT (for halt). HLT halted the processor until external reset or interrupt signals were received.
All processor commands were coded by one byte, but some of them were followed by one or two bytes of data, a memory address, or a port number. The register-to-register data-move commands were all coded by one byte, making up about a quarter of the commands in the processor-command system. The processor had eight one-byte commands to call the subroutines located at the fixed addresses 0000h, 0008h, 0010h, ... 0038h (RST). These commands were frequently used in the interrupt-handling or system-library calls.
The most sophisticated command (and the longest to execute) was XTHL, which was used for exchanging the register pair HL with the value stored at the address indicated by the stack pointer.
[edit] 16-bit operations
[vague]
Despite the fact that the 8080 was generally an 8-bit processor, it was also able to load immediate any register pair (LXI), increment or decrement any register pair (INX, DCX), add any register pair to the value in HL (DAD), switch HL with DE (XCHG) and perform a 16-bit arithmetical left shift of HL (DAD H) with one command. Hence some 16-bit operations were already possible. The only 16 bit instructions to affect the flags are the DADs, which set the CY (carry) flag.
[edit] Input/output scheme
[edit] Input output port space
The 8080 supported up to 256 input/output (I/O) ports, accessed via dedicated I/O instructions—taking port addresses as operands. This I/O mapping scheme was regarded as an advantage as it freed up the processor's limited address space. Many CPU architectures instead use a common address space without the need for dedicated I/O instructions, although a drawback in such designs may be that special hardware must be used to insert wait states as peripherals are often slower than memory. However, in some simple 8080 computers, I/O was indeed addressed as if they were memory cells, "memory mapped", leaving the I/O commands unused. I/O addressing could also sometimes employ the fact that the processor would output the same 8-bit port address at to both the lower and the higher address byte (i.e. IN 05h would put the address 0505h on the 16-bit address bus). Similar I/O-port schemes was used in the backward compatible Zilog Z80 and Intel 8085 as well as in the closely related x86 families of microprocessors.
[edit] Separate stack space
One of the bits in the processor state word (see below) was indicating that the processor is accessing data from the stack. Using this signal, it was possible to implement a separate stack memory space. However this feature was seldom used.
[edit] The internal state word
For more advanced systems, during one phase of its working loop the processor set its "internal state byte" on the data bus. This byte contains flags which indicate whether the memory or I/O port is accessed and whether it was necessary to handle an interrupt.
The interrupt system state (enabled or disabled) was also output on a separate pin. For simple systems, where the interrupts were not used, it is possible to find cases where this pin is used as an additional single-bit output port (the popular Radio86RK computer made in USSR, for instance).
[edit] Pin usage
The address bus had its own 16 pins, and the data bus had 8 pins that were possible to use without any multiplexing. Using the two additional pins (read and write signals), it was possible to assemble simple microprocessor devices very easily. Only the separate IO space, interrupts and DMA required additional chips to decode the processor pin signals. However the processor load capacity was limited, and even simple computers frequently contained bus amplifiers.
The processor required three power sources (-5, +5 and +12 Volt(V)) and two non-interlacing high-amplitude synchronization signals. However at least the late Soviet version КР580ВМ80А was able to work with a single +5 V power source, the +12 V pin being connected to +5 V and the -5 V pin to ground. The processor consumed about 1.3 watts (W) of power.
The pinout table, from the chip's accompanying documentation, described the pins as follows:
| Pin number | Signal | Type | Comment |
|---|---|---|---|
| 1 | A10 | Output | Address bus 10 |
| 2 | GND | - | Ground |
| 3 | D4 | Bidirectional | Bidirectional data bus. The processor also transiently sets here the "processor state", providing information that the processor is currently doing:
|
| 4 | D5 | ||
| 5 | D6 | ||
| 6 | D7 | ||
| 7 | D3 | ||
| 8 | D2 | ||
| 9 | D1 | ||
| 10 | D0 | ||
| 11 | -5 V | - | The -5 V power supply. This must be the first power source connected and the last disconnected, otherwise the processor will be damaged. |
| 12 | R | Input | Reset. The signal forces execution of commands, located at address 0000. The content of other processor registers is not modified. This is an inverting input (the active level being logical 0) |
| 13 | DMA | Input | Direct memory access request. The processor is requested to switch the data and address bus to the high impedance ("disconnected") state. |
| 14 | INT | Input | Interrupt request |
| 15 | CLC2 | Input | The second phase of the clock generator signal |
| 16 | ACK INT | Output | The processor had two commands for setting 0 or 1 level on this pin. The pin normally was supposed to be used for interrupt control. However in simple computers it was sometimes used as a single bit output port for various purposes. |
| 17 | RD | Output | Read (the processor reads from memory or input port) |
| 18 | WR | Output | Write (the processor writes to memory or output port). This is an inverted output, the active level being logical zero. |
| 19 | S | Output | Active level indicates that the processor has put the "state word" on the data bus. The various bits of this state word provide additional information for supporting the separate address and memory spaces, interrupts, and direct memory access. This signal is required to pass through additional logic before it can be used to write the processor state word from the data bus into some external register. |
| 20 | 5 V | - | The + 5 V power supply |
|
|
|||
| 21 | ACK DMA | Output | Direct memory access confirmation. The processor switches data and address pins into the high impedance state, allowing another device to manipulate the bus |
| 22 | CLC1 | Input | The first phase of the clock generator signal |
| 23 | RDY | Input | Wait. With this signal it was possible to suspend the processor's work. It was also used to support the hardware-based step-by step debugging mode. |
| 24 | WAIT | Output | Wait (indicates that the processor is in the waiting state) |
| 25 | A0 | Output | Address bus |
| 26 | A1 | ||
| 27 | A2 | ||
| 28 | 12 V | - | The +12 V power supply. This must be the last connected and first disconnected power source. |
| 29 | A3 | Output | The address bus, can switch into high impedance state on demand |
| 30 | A4 | ||
| 31 | A5 | ||
| 32 | A6 | ||
| 33 | A7 | ||
| 34 | A8 | ||
| 35 | A9 | ||
| 36 | A15 | ||
| 37 | A12 | ||
| 38 | A13 | ||
| 39 | A14 | ||
| 40 | A11 | ||
Literature, used for this table:
- http://tehno-doc.nm.ru/mikroshem_rus/kr580/kr580vm80a.html
- http://www.radiomaster.ru/stati/radio/k580/14_k580.php
[edit] Physical implementation
The 8080 integrated circuit used enhancement load nMOS gates and was manufactured in a process using a minimum feature size of 6 µm. A single layer of metal was used to interconnect the approximately 6,000 transistors[1] in the design (the higher resistance polysilicon layer required to implement transistor gates was also used for some interconnects). The die size was approximately 20 mm².
[edit] The industrial impact
[edit] Applications and successors
The 8080 was used in many early microcomputers, such as the MITS Altair 8800 Computer, Processor Technology SOL-20 Terminal Computer and IMSAI 8080 Microcomputer, forming the basis for machines running the CP/M operating system (the later, fully compatible and more capable, Zilog Z80 processor would capitalize on this, with Z80 & CP/M becoming the dominant CPU & OS combination of the period much like x86 & MS-DOS for the PC a decade later). The first single-board microcomputer (see the May 1976 issue of Radio-Electronics) called the "dyna-micro" was based on the Intel C8080A, and also used Intel's first EPROM, the C1702A. The dyna-micro was re-branded by E&L Instruments of Derby, CT in 1976 as the "MMD-1" (Mini-Micro Designer 1) and was made famous as the example microcomputer in the very popular 8080 "BugBook" series of the time. One of the early uses of the 8080 was made in the late 1970s by Cubic-Western Data of San Diego, CA in its Automated Fare Collection Systems custom designed for mass transit systems such as BART and others around the world. An early industrial use of the 8080 was as the "brain" of the DatagraphiX Auto-COM (Computer Output Microfiche) line of products which took large amounts of user data from reel-to-reel tape and imaged it onto microfiche. The Auto-COM instruments also included an entire automated film cutting, processing, washing, and drying sub-system - quite a feat, both then and in the 21st century, to all be accomplished successfully with only an 8-bit microprocessor running at a clock speed of less than 1MHz with a 64K byte memory limit. In addition, several early arcade video games were built around the 8080 microprocessor. Space Invaders was perhaps the most popular such title.
Shortly after the launch of the 8080, the Motorola 6800 competing design was introduced, and after that, the MOS Technology 6502 variation of the 6800. Zilog introduced the Z80, which had a compatible machine-language instruction set and initially used the same assembly language as the 8080, but for legal reasons, Zilog developed a syntactically-different alternative assembly language for the Z80. At Intel, the 8080 was followed by the compatible and electrically more elegant 8085, and later by the assembly language compatible 16-bit 8086 and then the 8/16-bit 8088, which was selected by IBM for its new PC to be launched in 1981. Later NEC made a NEC V20 processor (a 8088 clone) which supported 8080 emulation mode. Thus, the 8080, via its ISA, made a lasting impact on computer history.
The Soviet Union manufactured a complete 8080 analog named KP580ИK80 (later marked as KP580BM80), where even the pins were placed identically. This processor was the base of the Radio86RK (Радио 86РК in Russian), probably the most popular amateur single-board computer in the Soviet Union. Radio86RK's predecessor was the Micro-80 (Микро-80 in Russian), and its successor the Orion-128 (Орион-128 in Russian) which had a graphical display. Both were built on the KP580 processor. According to some sources, the Soviet analog had two undocumented instructions, specific to itself; however, these were not widely known.
Another model compatible with Intel 8080A, named MMN8080, was produced at Microelectronica Bucharest in Romania[2].
[edit] Industry change
The 8080 also changed how computers were created. When the 8080 was introduced, computer systems were usually created by computer manufacturers such as Digital Equipment Corporation, Hewlett Packard, or IBM. A manufacturer would produce the entire computer, including processor, terminals, and system software such as compilers and operating system. The 8080 was actually designed for just about any application except a complete computer system. Hewlett Packard developed the HP 2640 series of smart terminals around the 8080. The HP 2647 was a terminal which ran BASIC on the 8080. Microsoft would create the first popular programming language for the 8080, and would later acquire DOS for the IBM-PC.
As the 8080 evolved into the largely compatible x86 family, PCs evolved into workstations and servers of 16, 32 and 64 bits, with advanced memory protection, segmentation, and multiprocessing features, blurring the difference between small and large computers (the 80286 and 80386's protected mode were important in doing so). The size of chips has grown so that the size and power of large x86 chips is not much different from high end architecture chips, and a common strategy to produce a very large computer is to network many x86 processors.
The basic architecture of the 8080 and its successors has replaced many proprietary midrange and mainframe computers, and withstood challenges of technologies such as RISC. Most computer manufacturers have abandoned producing their own processors below the highest performance points. Though x86 may not be the most elegant, or theoretically most efficient design, the sheer market force of so many dollars going into refining a design has made the x86 family today, and will remain for some time, the dominant processor architecture, even bypassing Intel's attempts to replace it with incompatible architectures such as the iAPX 432 and Itanium.
[edit] History
Federico Faggin was the originator of the 8080 architecture in early 1972, proposed it to Intel's management and pushed for its implementation. He finally got the permission to develop it six months later. Faggin hired Masatoshi Shima from Japan who did the detailed design under his direction. Stan Mazor contributed a couple of instructions to the instruction set.
[edit] Patent
- US4,010,449 (1977-03-01) Federico Faggin, Masatoshi Shima, Stanley Mazor MOS computer employing a plurality of separate chips
[edit] Cultural impact
- Asteroid 8080 Intel is named as a pun and praise on the name of Intel 8080. [1]
- Microsoft's published phone number, 425-882-8080, was chosen because so much early work was on this chip.
[edit] See also
[edit] References
[edit] External links
- Intel and other manufacturers' 8080 CPU images and descriptions at cpu-collection.de
- Scan of the Intel 8080 data book at datasheetarchive.com
This article was originally based on material from the Free On-line Dictionary of Computing, which is licensed under the GFDL.
|
|||||||||||||||||
